Fiber
|
Wavelength
|
1310-1550nm
|
Bit rate
|
10Gbps
|
Tx power
|
＞-5db
|
Rx sensitivity
|
＞-14db
|
Fiber connector
|
LC
|
Video
|
Video bandwidth
|
10Gbps
|
Maximum resolution
|
4096*2160@30Hz downward compatibility
|
Maximum pixel clock
|
297MHZ
|
Effective cable length
|
10M
|
Physical interface
|
HDMI female
|
KVM(USB)
|
Version
|
1.1
|
Tx physical interface
|
USB female type B
|
Rx physical interface
|
USB female type A
|
Audio
|
Sampling frequency
|
48K
|
Sampling depth
|
24bit
|
Dynamic bandwidth
|
96db
|
Total harmonical distortion (THD)
|
-88db
|
Signal to noise ratio（SNR）
|
96db
|
Audio input/output impedance
|
600Ω
|
Signal level
|
VPP 3.5V
|
Physical interface
|
3.5mm stereo audio socket
|
Signal type
|
stereo audio
|
IR
|
Parameter
|
Min
|
Type
|
Max
|
Unit
|
Condition
|
Optical current
|
200
|
-
|
1030
|
ｕA
|
IF=4mA,VCE=3.5V
|
Peak wavelength
|
-
|
940
|
-
|
nm
|
1F=20mA
|
Spectrum voltage
|
-
|
80
|
-
|
nm
|
1F=20mA
|
View angle
|
-
|
±30
|
-
|
Deg
|
1F=20mA
|
Forward voltage
|
-
|
1.2
|
1.6
|
V
|
1F=20mA
|
Reverse current
|
-
|
-
|
10
|
ｕA
|
VR=5V
|
RS232 (3-wire system, full duplex)
|
Baud rate
|
256000Hz downward compatibility
|
Data bits
|
8 digits
|
Physical interface
|
3-pin phoenix terminal
|
RS 485 (2-wire system, half duplex)
|
Error rate
|
<10^-9
|
Bit rate
|
0-400Kbps
|
Physical interface
|
3-pin phoenix terminal
|
Contact closure
|
Input electrical parameters
|
Dry node, not charged (short or disconnected)
|
Output electrical parameters
|
Dry node, not charged (short or disconnected)
|
Output relay maximum switching voltage
|
250VAC/220VDC
|
Output relay maximum switching current
|
2A
|
Mechanical durability of output relay
|
100,000,000times
|
Maximum output power of relay
|
60W
|
Physical interface
|
2-pin phoenix terminal (transmitter)
Switch button (receiver)
|
Others
|
Operating temperature
|
-20°C ~75°C
|
Storage temperature
|
-40°C ~85°C
|
Power supply
|
12V1A
|
Power dissipation
|
＜1.5W
|
Product schematic connection diagram
|
Product configuration
|
Unit
|
Fiber type
|
Specification
|
|
1 channel 4K HDMI video with loop out + 1 channel bidirectional 3.5 audio +1 channel revers IR+1channel bidirectional RS232 data fiber optical converter
|
Pair
|
Single fiber/single mode
|
Conventional
|
|
1 channel 4K HDMI video with loop out+ 1 channel bidirectional 3.5 audio +1 channel revers IR+1channel bidirectional RS232 data + KVM fiber optical converter
|
Pair
|
Single fiber/single mode
|
Conventional
|
|
1 channel 4K HDMI video with loop out+ 1 channel bidirectional 3.5 audio +1 channel revers IR+1channel bidirectional RS232 data + 1 channel reverse contact closure + KVM fiber optical converter
|
Pair
|
Single fiber/single mode
|
Unconventional
|
|
1 channel 4K HDMI video with loop out + 1 channel bidirectional 3.5 audio +1 channel revers IR+1 channel bidirectional RS485 data fiber optical converter
|
Pair
|
Single fiber/single mode
|
Conventional
|
|
1 channel 4K HDMI video with loop out + 1 channel bidirectional 3.5 audio +1 channel revers IR+1channel bidirectional RS485 data + KVM fiber optical converter
|
Pair
|
Single fiber/single mode
|
Conventional
|
|
1 channel 4K HDMI video with loop out + 1 channel bidirectional 3.5 audio +1 channel revers IR+1channel bidirectional RS232 data + 1 channel reverse contact closure + KVM fiber optical converter
|
Pair
|
Single fiber/single mode
|
Unconventional
|
Attention
Lightning protection, static electricity and grounding:
It is recommended that when install the device, consideration should be given to the impact of grounding by lightning, and take prevention measures. Strong static electricity will damage the optical device and data chip in the equipment. It is recommended that when plug/unplug the data port of the optical converter, please disconnect the power supply of the optical converter first.
Fiber and optical components:
Be careful when plugging the optical fiber as optical components of the optical converter is very fragile, and it should avoid causing damage to the optical components. It should be noted that the light source produced by the optical components of the optical converter will be harmful to eyes, so do not have direct eye contact with the optical components of optical converter. If you need to detect the optical power of the optical converter, please use the optical power meter.
Equipment and installation procedures:
（1）Optical fiber installation: please carefully insert the optical fiber into the optical fiber interface of the optical terminal after confirming that the optical fiber link meets the installation requirements.
（2）Equipment installation: The equipment can be distinguished between transmitter and receiver, and it is stated clearly on the label and printed on the chassis of the equipment.
Reviews
There are no reviews yet.